Connexion

Forum

Système et matériels » Autres matériels et périphériques [Réglé] port sur banana-pi/pro Cherche de l'aide

Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 21/09/2019 à 12h09
Bonjour la communauté !

Voilà, j'ai pu récupérer quelques ressources :
Le script de création d'image par Dtux :
git clone https://git.labolyon.fr/DTux/mageia4arm.git
Récupérer les sources pour le banana-pro (et un autre Mageian tente du banana-pi, mêmes sources, mais il est non-francophone).
git clone --recursive https://github.com/LeMaker/lemaker-bsp.git

De la documentation :
DTS : https://linux-sunxi.org/Device_Tree
FEX : https://linux-sunxi.org/Script.bin
Étapes pour avoir un OS (sans distrib) : http://wiki.lemaker.org/BananaPro/Pi:Building_u-boot,_script.bin_and_linux-kernel#Installation

Il y a là surement 90% des informations nécessaires, mais je n'ai aucune idée de l'entre-coupage, qu'est-ce que je dois suivre de Lemaker, qu'est-ce que je dois prendre de Mageia...

Parmi mes interrogations :
Le noyau, est-ce que le noyau de Mageia est "générique" et obtient les modules avec la DTB (enfin, script.bin) depuis le chargeur de démarrage ? Ou est-ce que je dois m'occuper de mettre à jour le noyau régulièrement (voire, ajouter cette version du noyau pour banana-p* au BuildSystem de Mageia.org ?)
Comment ajouter la partie "build u-boot" au processus de mageia4arm ? Même question pour le build de script.bin

Bref, grande aventure, c'est un peu comme le seigneur des anneaux, sans carte, sans communauté...
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 23/09/2019 à 07h52
Bien, pour le noyau linux, on remercie tous notre gourou du noyau !
Citation :
[dimanche 22 septembre 2019] [20:56:50 CEST] <Jybz> Hello, tmb, do you know if there is something special to do about the kernel for sunxi chipsets (allwinners), are the kernels in Mageia ready ?
[dimanche 22 septembre 2019] [20:58:49 CEST] <tmb> Jybz, armv7 or aarch64 ?
[dimanche 22 septembre 2019] [20:58:56 CEST] <Jybz> armv7
[dimanche 22 septembre 2019] [20:59:32 CEST] <Jybz> I'm trying to port for Banana Pro (and Banana Pi)
[dimanche 22 septembre 2019] [20:59:36 CEST] <Jybz> a SBC
[dimanche 22 septembre 2019] [21:00:19 CEST] <tmb> Jybz, looking at the kernel defconfigs, they are not enabled, will do so for next build
[dimanche 22 septembre 2019] [21:01:08 CEST] <Jybz> Perfect ! Thank you ![...]


C'est loin d'être fini. Uboot, Mageia, Script.bin et création d'une image.
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 28/09/2019 à 12h28
Je confirme que les noyau pour les SOC allwinner on été activé pour Mageia7 et Cauldron :

Cauldron, 1444676:
http://svnweb.mageia.org/packages/cauldron/kernel/current/SOURCES/defconfig-arm-desktop?view=log
Mageia7, 1444677 :
http://svnweb.mageia.org/packages/updates/7/kernel/current/SOURCES/defconfig-arm-desktop?view=log
Edité par Jybz Le 28/09/2019 à 12h29
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 04/10/2019 à 22h27
Bon, apparemment, j'ai semi-fail :
Code TEXT :
U-Boot SPL 2019.01-rc3-g829407b58f (Sep 28 2019 - 15:47:33 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
 
 
U-Boot 2019.01-rc3-g829407b58f (Sep 28 2019 - 15:47:33 +0200) Allwinner Technology
 
CPU:   Allwinner A20 (SUN7I)
Model: LeMaker Banana Pro
I2C:   ready
DRAM:  1 GiB
MMC:   MMC0: 01c20060 = 0x200c140, 01c20088 = 0x8140030b, 00000000 = 0xea000016
MMC3: 01c20060 = 0x200c940, 01c20094 = 0x0, 00000000 = 0xea000016
mmc@1c0f000: 0, mmc@1c12000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment
 
Setting up a 720x576i composite-pal console (overscan 32x20)
In:    serial
Out:   vga
Err:   vga
SCSI:  SATA link 0 timeout.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst 
 
Net:   sunxi_set_gate: (CLK#66) unhandled
eth0: ethernet@1c50000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
USB2:   USB EHCI 1.00
USB3:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
344 bytes read in 1 ms (335.9 KiB/s)
## Executing script at 43100000
3437192 bytes read in 219 ms (15 MiB/s)
25166 bytes read in 7 ms (3.4 MiB/s)
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
EHCI failed to shut down host controller.
   Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 

à savoir :
Code TEXT :
bootargs='console=ttyS0,115200 disp.screen0_output_mode=EDID:1024x768p50 hdmi.audio=EDID:0 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait'
fatload mmc 0:1 0x40008000 vmlinuz
fatload mmc 0:1 0x44000000 sun7i-a20-bananapro.dtb
bootz 0x40008000 - 0x44000000 
 

Donc DTB à 44000000, c'est différent de 0x40008000... Où est le problème ?
   
funix Membre non connecté

Rang

Avatar

Inscrit le : 17/12/2012 à 21h03

Messages: 542

Le 04/10/2019 à 22h31
je trouve cool la manière dont tu alimentes ce thread :D tu dois bien être le seul ici à tester l'aventure. Cela dit je vais sûrement m'y mettre, j'ai bricolé vite fait une alarme vidéo avec la webcam comme capteur, le logiciel motion qui détecte le mouvement et enregistre une vidéo, j'y accède via internet après avoir reçu un mail (voir par là https://olivier.hoarau.org/?p=3842 ). Ca fait un peu riche comme solution, un PC+un serveur alimenté en permanence, c'est pas très écolo, j'envisage donc d'utiliser ces mini PC. Edité par funix Le 04/10/2019 à 22h32


FUNIX - http://www.funix.org
Mettez un pingouin dans votre PC
Blog - http://olivier.hoarau.org
Site web    
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 05/10/2019 à 09h01
Salut funix, ton projet à l'air chouette !
Pourquoi n'ajoutes du pas la vidéo en pièce jointe ? Peur de saturer la boite mail ? Vidéo trop grosse ? Temps d'upload trop long et évènement "trop tard" ?
Effectivement, un PC rien que pour ça, c'est un peu gros. Si tu veux, on peut en parler, surtout si tu mets Mageia sur la raspberry-pi (ou banana-pi/pro, bientôt ça sera possible :D ). D'ailleurs, quand tu dis mini-PC, tu parles vraiment d'un mini-PC avec une très petite carte mère dans une "tour", ou tu parles d'une SBC (Single Board Computer) style Raspberry-pi ?
D'un autre coté, avec tous ses services noip etc, je pense que tu peux alléger fort l'architecture. Est-ce qu'un nom de domaine rien que pour ça est nécessaire ? Pourquoi ne pas prendre l'IPv4 ? Voir l'IPv6 et éviter la config d'un NAT ? Et si tu ne veux pas mémoriser l'adresse IP, tu peux faire un script qui renvoie d'adresse IP par mail lorsqu'elle change, et changer le fichier host pour ne mémoriser qu'une chaine de caractère au lieu de l'IP (par exemple "http://mavideo").
Est-ce que pour la détection tu utilise opencv ? etc.
Si tu veux, on peut en parler sur un nouveau sujet MLO pour approfondir la discussion ?
   
funix Membre non connecté

Rang

Avatar

Inscrit le : 17/12/2012 à 21h03

Messages: 542

Le 05/10/2019 à 09h30
oui vidéo trop grosse, mon serveur fait tampon en stockant les vidéos (donc ça fait 2 PC au total et non 1), apache tourne sur le serveur et donne l'accès sécurisé via le web, j'y accède via mon téléphone portable sous lineageos. Oui quand je dis mini pc c'est un peu impropre c'est plutôt un truc du style comme banana-pi ou raspberry-pi, il faut que j'arrive à tout faire tourner dessus, détection, stockage, mail d'alarme et accès du web. Pour le nom de domaine et l'adresse ip, à l'époque où ce genre de service n'existait pas j'utilisais ce genre de script, mais franchement maintenant avec noip c'est beaucoup plus simple.
Pour la détection, c'est un soft qui s'appelle motion (voir le lien de mon message précédent)


FUNIX - http://www.funix.org
Mettez un pingouin dans votre PC
Blog - http://olivier.hoarau.org
Site web    
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 08/10/2019 à 16h05
Bon, j'ai changé plein de trucs :

Au lieu d'avoir une partition vfat pour y placer le noyau et les variables de uboot, j'ai viré ça.
À la place, j'utilise directement la partition racine de Mageia.
Inconvénient : chiffrement, droits d'accès à la partition boot de la SD lors du développement (faut être root quoi)
avantage : pas de partition a gérer lors des probables mises à jour de noyau (mount, update, umount...) utilisation des liens symboliques (notamment vmlinuz),

J'utilise uboot de denx, la source uboot au lieu du dépot par sunxi.
J'ai donc activé le support ext4 d'Uboot, désactiver le support de l'usb (car c'était trop long à démarrer, vérifier chaque port USB).

Bien sûr, modifié le script de Dtux pour ajouter une option si la partition boot est séparée de la racine.

Mais voilà... Je suis toujours avec la même erreur...

(exemple avec un démarre à la main, sans utiliser les scripts de démarrage)
Code BASH :
 
U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 08 2019 - 14:52:20 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
 
U-Boot 2019.10-rc4-00037-gdac51e9aaf (Oct 08 2019 - 14:52:20 +0200) Allwinner Technology
 
CPU:   Allwinner A20 (SUN7I)
Model: LeMaker Banana Pro
I2C:   ready
DRAM:  1 GiB
MMC:   mmc@1c0f000: 0, mmc@1c12000: 1
Loading Environment from EXT4... OK
Setting up a 720x576i composite-pal console (overscan 32x20)
In:    serial
Out:   vga
Err:   vga
Net:   eth0: ethernet@1c50000
starting USB...
No working controllers found
Hit any key to stop autoboot:  0 
 
$ setenv bootargs console=ttyS0,115200 disp.screen0_output_mode=EDID: 1024x768p50 hdmi.audio=EDID:0 root=/dev/mmcblk0 ottp=x lvo=eln owi
 
$ ext4load mmc 0:1 0x40008000 /boot/vmlinuz
3437192 bytes read in 190 ms (17.3 MiB/s)
 
$ ext4load mmc 0:1 0x48000000 /boot/sun7i-a20-bananapro.dtb
25166 bytes read in 4 ms (6 MiB/s)
 
$ help bootz
bootz - boot Linux zImage image from memory
 
Usage:
bootz [addr [initrd[:size]] [fdt]]
- boot Linux zImage stored in memory
The argument 'initrd' is optional and specifies the address
of the initrd in memory. The optional argument ':size' allows
specifying the size of RAW initrd.
When booting a Linux kernel which requires a flat device-tree
a third argument is required which is the address of the
device-tree blob. To boot that kernel without an initrd image,
use a '-' for the second argument. If you do not pass a third
a bd_info struct will be passed instead
 
$ bootz 0x40008000 - 0x48000000
## Flattened Device Tree blob at 48000000
Booting using the fdt blob at 0x48000000
Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 


   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 08/10/2019 à 16h55
(d'ailleurs, la branche des scripts de Dtux que je modifie : https://git.labolyon.fr/Jybz/mageia4arm )
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 09/10/2019 à 20h39
Ah !
J'ai flashé l'image de Fedora, j'ai tenté, il se lance.
J'ai flashé l'U-Boot que j'ai compilé sur la carte, et là, il uboot plus le kernel ! Stop à "Starting Kernel..."

J'ai peut-être un problème d'Uboot et pas de kernel. Mais quoi ?
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 13/10/2019 à 15h44
Lecture :

https://wiki.debian.org/InstallingDebianOn/Allwinner#Mainline_kernel_and_linux-sunxi.org_3.4_kernel

Noyau, sunxi-linux vs linux :
implémentation pour le graphique boitant pour la version standard de linux, mais un support depuis 2016 grace à uboot.
Debian utilise le noyau linux standard.

Uboot vs sunxi-uboot vs allwinner-uboot :
Il faut oublier allwinner-uboot.
sunxi-uboot : intéressant pour les vieux matériels qui ne sont pas maintenu dans le u-boot traditionnel.
Debian utiliserait le uboot standard.

Bah voilà ! On serait bon, j'utilise les deux trucs standard. Mais pourquoi ça ne démarre toujours pas ? (!!!)
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 13/10/2019 à 20h10
Code BASH :
U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
 
 
U-Boot 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200) Allwinner Technology For Mageia
 
CPU:   Allwinner A20 (SUN7I)
Model: LeMaker Banana Pro
I2C:   ready
DRAM:  1 GiB
MMC:   mmc@1c0f000: 0, mmc@1c12000: 1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
 
** Unable to read "/boot/uboot.env" from mmc0:1 **
In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@1c50000
starting USB...
No working controllers found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
$ setenv bootargs debug earlyprintk console=tty0,115200 root=/dev/mmcblk0p1 rootfstype=ext4 elevator=deadline rootwait ddebug_query=KNL earlycon=KNL
$ ext4load mmc 0:1 0x44000000 /boot/vmlinuz
3437552 bytes read in 191 ms (17.2 MiB/s)
$ ext4load mmc 0:1 0x40008000 /boot/sun7i-a20-bananapro.dtb
25166 bytes read in 4 ms (6 MiB/s)
$ bootz 0x44000001 - 0x40008000
$ bootz 0x44000001 - 0x40008000
$ bootz 0x44000001 - 0x40008000
$ bootz 0x44000000 - 0x40008000
## Flattened Device Tree blob at 40008000
   Booting using the fdt blob at 0x40008000
   Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 
 
 


je remarque que bootz ne fonctionne pas si le contenu à l'adresse donné n'est pas ce qu'il attends (il attends un noyau compressé).
Je remarque qu'il lit la DTB.

Mais je ne sais toujours pas pourquoi il ne démarre pas.

Dois-je abandonner ?
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 13/10/2019 à 20h18
Code BASH :
cat ./arch/arm/dts/*bananapro*.dts | grep "chosen" -A 1
        chosen {
                stdout-path = "serial0:115200n8";

du coup, on teste avec serial0 !

Code BASH :
bootargs=debug earlyprintk console=serial0,115200 root=/dev/mmcblk0p1 rootfstype=ext4 elevator=deadline rootwait ddebug_query=KNL earlycon=KNL
$ ext4load mmc 0:1 0x44000000 /boot/vmlinuz
3437552 bytes read in 190 ms (17.3 MiB/s)
$ ext4load mmc 0:1 0x40008000 /boot/sun7i-a20-bananapro.dtb
25166 bytes read in 4 ms (6 MiB/s)
$ bootz 0x44000000 - 0x40008000
## Flattened Device Tree blob at 40008000
   Booting using the fdt blob at 0x40008000
   Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 

Rien... Déception encore.
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 19/10/2019 à 12h42
Bonne et mauvaise nouvelles !

J'ai téléchargé les dernières sources sur kernel.org

J'ai compilé avec ARCH=arm et GCC=arm-truc avec comme defconf sunxi, en modifiant juste avec make xconfig l'image compressée en lzma au lieu de... celui par défaut.

Après flashage, sur la console nous avons :
Code BASH :
Bienvenue avec minicom 2.7.1
 
OPTIONS: I18n 
Compilé le Sep 28 2018, 03:52:42.
Port /dev/ttyUSB0, 12:35:58
 
Tapez CTRL-A Z pour voir l'aide concernant les touches spéciales
 
 
U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
 
 
U-Boot 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200) Allwinner Technology For Mageia
 
CPU:   Allwinner A20 (SUN7I)
Model: LeMaker Banana Pro
I2C:   ready
DRAM:  1 GiB
MMC:   mmc@1c0f000: 0, mmc@1c12000: 1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
 
** Unable to read "/boot/uboot.env" from mmc0:1 **
In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@1c50000
starting USB...
No working controllers found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
$ ext4load mmc 0:1 0x40008000 /boot/vmlinuz
3175896 bytes read in 176 ms (17.2 MiB/s)
$ ext4load mmc 0:1 0x48000000 /boot/sun7i-a20-bananapro.dtb
25166 bytes read in 4 ms (6 MiB/s)
$ bootz 0x40008000 - 0x48000000
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.0-rc3 (jibz@jabztop) (gcc version 8.2.1 20181105 (Red Hat Cross 8.2.1-2) (GCC)) #1 SMP Fri Oct 18 19:47:18 CEST 2019
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: LeMaker Banana Pro
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 MiB
[    0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 15 pages/cpu s30604 r8192 d22644 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 260608
[    0.000000] Kernel command line: 
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 930968K/1048576K available (6144K kernel code, 436K rwdata, 1696K rodata, 1024K init, 242K bss, 19304K reserved, 98304K cma-reserved, 262144K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x2ac/0x43c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000020] Switching to timer-based delay loop, resolution 41ns
[    0.000427] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000734] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000991] Console: colour dummy device 80x30
[    0.001361] printk: console [tty0] enabled
[    0.001413] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.001442] pid_max: default: 32768 minimum: 301
[    0.001607] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.001640] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.002476] CPU: Testing write buffer coherency: ok
[    0.002938] /cpus/cpu@0 missing clock-frequency property
[    0.002976] /cpus/cpu@1 missing clock-frequency property
[    0.003000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.003637] Setting up static identity map for 0x40100000 - 0x40100060
[    0.003808] rcu: Hierarchical SRCU implementation.
[    0.004389] smp: Bringing up secondary CPUs ...
[    0.015175] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.015338] smp: Brought up 1 node, 2 CPUs
[    0.015379] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.015394] CPU: All CPU(s) started in HYP mode.
[    0.015406] CPU: Virtualization extensions available.
[    0.016122] devtmpfs: initialized
[    0.022004] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.022327] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.022376] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.026030] pinctrl core: initialized pinctrl subsystem
[    0.027218] NET: Registered protocol family 16
[    0.028547] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.029683] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.029718] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.048352] SCSI subsystem initialized
[    0.048931] usbcore: registered new interface driver usbfs
[    0.049025] usbcore: registered new interface driver hub
[    0.049101] usbcore: registered new device driver usb
[    0.049379] pps_core: LinuxPPS API ver. 1 registered
[    0.049404] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.049441] PTP clock support registered
[    0.049713] Advanced Linux Sound Architecture Driver Initialized.
[    0.050662] clocksource: Switched to clocksource arch_sys_counter
[    0.058836] thermal_sys: Registered thermal governor 'step_wise'
[    0.059331] NET: Registered protocol family 2
[    0.059956] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.060010] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.060113] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.060260] TCP: Hash tables configured (established 8192 bind 8192)
[    0.060415] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.060496] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.060831] NET: Registered protocol family 1
[    0.061608] RPC: Registered named UNIX socket transport module.
[    0.061649] RPC: Registered udp transport module.
[    0.061663] RPC: Registered tcp transport module.
[    0.061676] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.062210] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.062499] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.064184] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    0.072127] NFS: Registering the id_resolver key type
[    0.072194] Key type id_resolver registered
[    0.072210] Key type id_legacy registered
[    0.072325] bounce: pool size: 64 pages
[    0.072385] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.072409] io scheduler mq-deadline registered
[    0.072424] io scheduler kyber registered
[    0.073795] sun4i-usb-phy 1c13400.phy: Couldn't get regulator usb1_vbus... Deferring probe
[    0.077532] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.137555] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.139635] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[    0.160887] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 48, base_baud = 1500000) is a U6_16550A
[    0.771386] printk: console [ttyS0] enabled
[    0.776091] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
[    0.808653] 1c29000.serial: ttyS1 at MMIO 0x1c29000 (irq = 49, base_baud = 1500000) is a U6_16550A
[    0.818137] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator
[    0.850663] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 50, base_baud = 1500000) is a U6_16550A
[    0.960703] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    0.968218] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[    0.974146] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    0.983140] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc 
[    0.992226] scsi host0: ahci-sunxi
[    0.996098] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 36
[    1.005993] libphy: Fixed MDIO Bus: probed
[    1.010118] CAN device driver interface
[    1.014608] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pa not found, using dummy regulator
[    1.024434] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
[    1.030848] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
[    1.036893] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[    1.042679] sun7i-dwmac 1c50000.ethernet: no reset control found
[    1.049492] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.056095] ehci-platform: EHCI generic platform driver
[    1.061792] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.068012] ohci-platform: OHCI generic platform driver
[    1.075531] sunxi-rtc 1c20d00.rtc: registered as rtc0
[    1.080813] i2c /dev entries driver
[    1.085318] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[    1.106039] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[    1.115996] axp20x-regulator axp20x-regulator: regulators node not found
[    1.122777] ldo1: supplied by regulator-dummy
[    1.127392] ldo2: supplied by regulator-dummy
[    1.132462] ldo3: supplied by regulator-dummy
[    1.137507] ldo4: supplied by regulator-dummy
[    1.142105] ldo5: supplied by regulator-dummy
[    1.147137] dcdc2: supplied by regulator-dummy
[    1.152256] dcdc3: supplied by regulator-dummy
[    1.157873] axp20x-i2c 0-0034: AXP20X driver loaded
[    1.164330] Registered IR keymap rc-empty
[    1.168469] rc rc0: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0
[    1.175335] input: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0/input1
[    1.182995] sunxi-ir 1c21800.ir: initialized sunXi IR driver
[    1.189955] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.200868] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pf not found, using dummy regulator
[    1.211453] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    1.241532] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[    1.249709] sunxi-mmc 1c12000.mmc: allocated mmc-pwrseq
[    1.278434] sunxi-mmc 1c12000.mmc: initialized, max. request size: 16384 KB
[    1.286075] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pg not found, using dummy regulator
[    1.296391] sun4i-ss 1c15000.crypto-engine: Die ID 0
[    1.305230] usbcore: registered new interface driver usbhid
[    1.310894] usbhid: USB HID core driver
[    1.316006] random: fast init done
[    1.321625] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.330880] debugfs: Directory '1c22c00.codec' with parent 'sun4i-codec' already present!
[    1.339814] mmc0: new high speed SDHC card at address 5048
[    1.341593] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[    1.352459] ata1: SATA link down (SStatus 0 SControl 300)
[    1.354277] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.359379] NET: Registered protocol family 17
[    1.364029] mmcblk0: mmc0:5048 SD32G 29.0 GiB 
[    1.367919] can: controller area network core (rev 20170425 abi 9)
[    1.374452] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.378736] NET: Registered protocol family 29
[    1.385675] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.388608] can: raw protocol (rev 20170425)
[    1.396779] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.398374] can: broadcast manager protocol (rev 20170425 t)
[    1.409538] can: netlink gateway (rev 20190810) max_hops=1
[    1.415415] Key type dns_resolver registered
[    1.418990] mmc1: new high speed SDIO card at address 0001
[    1.419723] Registering SWP/SWPB emulation handler
[    1.445589] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pa not found, using dummy regulator
[    1.455502] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
[    1.461933] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
[    1.467963] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[    1.473774] sun7i-dwmac 1c50000.ethernet: no reset control found
[    1.481899]  mmcblk0: p1
[    1.590962] sun7i-dwmac 1c50000.ethernet: Version ID not available
[    1.597178] sun7i-dwmac 1c50000.ethernet:    DWMAC1000
[    1.602197] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
[    1.609426] sun7i-dwmac 1c50000.ethernet: Normal descriptors
[    1.615103] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
[    1.620945] libphy: stmmac: probed
[    1.626317] ehci-platform 1c14000.usb: EHCI Host Controller
[    1.631996] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.640119] ehci-platform 1c14000.usb: irq 33, io mem 0x01c14000
[    1.670675] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[    1.677660] hub 1-0:1.0: USB hub found
[    1.681515] hub 1-0:1.0: 1 port detected
[    1.686412] ehci-platform 1c1c000.usb: EHCI Host Controller
[    1.692095] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.700174] ehci-platform 1c1c000.usb: irq 37, io mem 0x01c1c000
[    1.730667] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    1.737624] hub 2-0:1.0: USB hub found
[    1.741476] hub 2-0:1.0: 1 port detected
[    1.746350] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[    1.753066] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[    1.761140] ohci-platform 1c14400.usb: irq 34, io mem 0x01c14400
[    1.835504] hub 3-0:1.0: USB hub found
[    1.839320] hub 3-0:1.0: 1 port detected
[    1.844276] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[    1.851001] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[    1.859483] ohci-platform 1c1c400.usb: irq 38, io mem 0x01c1c400
[    1.935535] hub 4-0:1.0: USB hub found
[    1.939351] hub 4-0:1.0: 1 port detected
[    1.943871] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01T00:01:38 UTC (98)
[    1.952320] ALSA device list:
[    1.955306]   #0: sun4i-codec
[    1.959338] VFS: Cannot open root device "(null)" or unknown-block(0,0): error -6
[    1.966882] Please append a correct "root=" boot option; here are the available partitions:
[    1.975278] b300        30375936 mmcblk0 
[    1.975283]  driver: mmcblk
[    1.982102]   b301         3998976 mmcblk0p1 f67e610d-01
[    1.982104] 
[    1.988909] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[    1.997178] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc3 #1
[    2.003355] Hardware name: Allwinner sun7i (A20) Family
[    2.008610] [<c010ed54>] (unwind_backtrace) from [<c010b488>] (show_stack+0x10/0x14)
[    2.016365] [<c010b488>] (show_stack) from [<c06a5f40>] (dump_stack+0x88/0x9c)
[    2.023598] [<c06a5f40>] (dump_stack) from [<c011da04>] (panic+0x110/0x2fc)
[    2.030569] [<c011da04>] (panic) from [<c0901320>] (mount_block_root+0x1cc/0x274)
[    2.038062] [<c0901320>] (mount_block_root) from [<c09014e8>] (mount_root+0x120/0x13c)
[    2.045987] [<c09014e8>] (mount_root) from [<c0901654>] (prepare_namespace+0x150/0x194)
[    2.053998] [<c0901654>] (prepare_namespace) from [<c06bc288>] (kernel_init+0x8/0x110)
[    2.061921] [<c06bc288>] (kernel_init) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[    2.069491] Exception stack(0xef04ffb0 to 0xef04fff8)
[    2.074544] ffa0:                                     00000000 00000000 00000000 00000000
[    2.082724] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    2.090903] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    2.097529] CPU1: stopping
[    2.100248] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.4.0-rc3 #1
[    2.106425] Hardware name: Allwinner sun7i (A20) Family
[    2.111658] [<c010ed54>] (unwind_backtrace) from [<c010b488>] (show_stack+0x10/0x14)
[    2.119408] [<c010b488>] (show_stack) from [<c06a5f40>] (dump_stack+0x88/0x9c)
[    2.126637] [<c06a5f40>] (dump_stack) from [<c010df5c>] (handle_IPI+0x1b0/0x1e4)
[    2.134040] [<c010df5c>] (handle_IPI) from [<c0394ed4>] (gic_handle_irq+0x8c/0x90)
[    2.141616] [<c0394ed4>] (gic_handle_irq) from [<c0101a8c>] (__irq_svc+0x6c/0x90)
[    2.149099] Exception stack(0xef087f78 to 0xef087fc0)
[    2.154151] 7f60:                                                       00000000 000019c4
[    2.162332] 7f80: ef7af474 c0117aa0 ffffe000 c0a04e68 c0a04ea4 00000002 c0a683e8 c07f3b7c
[    2.170512] 7fa0: 00000001 00000000 00000001 ef087fc8 c01087a4 c01087a8 60000013 ffffffff
[    2.178696] [<c0101a8c>] (__irq_svc) from [<c01087a8>] (arch_cpu_idle+0x38/0x3c)
[    2.186101] [<c01087a8>] (arch_cpu_idle) from [<c0147458>] (do_idle+0x110/0x154)
[    2.193505] [<c0147458>] (do_idle) from [<c0147744>] (cpu_startup_entry+0x18/0x1c)
[    2.201079] [<c0147744>] (cpu_startup_entry) from [<401024ac>] (0x401024ac)
[    2.208047] ---[ end Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) ]---
 
   
Jybz Membre non connecté

Rang

Avatar

Modérateur

Inscrit le : 10/10/2018 à 10h26

Messages: 1917

Le 19/10/2019 à 12h48
Mieux encore, j'avais oublié de préciser bootargs !

Code BASH :
U-Boot SPL 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
 
 
U-Boot 2019.10-rc4-00037-gdac51e9aaf (Oct 13 2019 - 12:47:46 +0200) Allwinner Technology For Mageia
 
CPU:   Allwinner A20 (SUN7I)
Model: LeMaker Banana Pro
I2C:   ready
DRAM:  1 GiB
MMC:   mmc@1c0f000: 0, mmc@1c12000: 1
Loading Environment from EXT4... ** File not found /boot/uboot.env **
 
** Unable to read "/boot/uboot.env" from mmc0:1 **
In:    serial
Out:   serial
Err:   serial
Net:   eth0: ethernet@1c50000
starting USB...
No working controllers found
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
$ setenv bootargs console=ttyS0,115200 disp.screen0_output_mode=EDID:1024x768p50 hdmi.audio=EDID:0 root=/dev/mmcblk0p1 rootfstype=ext4 elevator=deadline rootwait
$ ext4load mmc 0:1 0x40008000 /boot/vmlinuz
3175896 bytes read in 176 ms (17.2 MiB/s)
$ ext4load mmc 0:1 0x48000000 /boot/sun7i-a20-bananapro.dtb
25166 bytes read in 4 ms (6 MiB/s)
$ bootz 0x40008000 - 0x48000000
## Flattened Device Tree blob at 48000000
   Booting using the fdt blob at 0x48000000
   Loading Device Tree to 49ff6000, end 49fff24d ... OK
 
Starting kernel ...
 
�    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.4.0-rc3 (jibz@jabztop) (gcc version 8.2.1 20181105 (Red Hat Cross 8.2.1-2) (GCC)) #1 SMP Fri Oct 18 19:47:18 CEST 2019
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: LeMaker Banana Pro
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] Reserved memory: created CMA memory pool at 0x4a000000, size 96 MiB
[    0.000000] OF: reserved mem: initialized node default-pool, compatible id shared-dma-pool
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: Using PSCI v0.1 Function IDs from DT
[    0.000000] percpu: Embedded 15 pages/cpu s30604 r8192 d22644 u61440
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 260608
[    0.000000] Kernel command line: console=ttyS0,115200 disp.screen0_output_mode=EDID:1024x768p50 hdmi.audio=EDID:0 root=/dev/mmcblk0p1 rootfstype=ext4 elevator=deadline rootwait
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 930964K/1048576K available (6144K kernel code, 436K rwdata, 1696K rodata, 1024K init, 242K bss, 19308K reserved, 98304K cma-reserved, 262144K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] random: get_random_bytes called from start_kernel+0x2ac/0x43c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000007] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000020] Switching to timer-based delay loop, resolution 41ns
[    0.000429] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000736] clocksource: hstimer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370868154 ns
[    0.000995] Console: colour dummy device 80x30
[    0.001053] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.001068] pid_max: default: 32768 minimum: 301
[    0.001227] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.001245] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.002056] CPU: Testing write buffer coherency: ok
[    0.002495] /cpus/cpu@0 missing clock-frequency property
[    0.002517] /cpus/cpu@1 missing clock-frequency property
[    0.002533] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.003130] Setting up static identity map for 0x40100000 - 0x40100060
[    0.003282] rcu: Hierarchical SRCU implementation.
[    0.003843] smp: Bringing up secondary CPUs ...
[    0.014622] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.014786] smp: Brought up 1 node, 2 CPUs
[    0.014804] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[    0.014810] CPU: All CPU(s) started in HYP mode.
[    0.014815] CPU: Virtualization extensions available.
[    0.015518] devtmpfs: initialized
[    0.021685] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.021993] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.022023] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.025632] pinctrl core: initialized pinctrl subsystem
[    0.026798] NET: Registered protocol family 16
[    0.028273] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.029532] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.029547] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.048295] SCSI subsystem initialized
[    0.048844] usbcore: registered new interface driver usbfs
[    0.048921] usbcore: registered new interface driver hub
[    0.048989] usbcore: registered new device driver usb
[    0.049259] pps_core: LinuxPPS API ver. 1 registered
[    0.049267] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.049289] PTP clock support registered
[    0.049559] Advanced Linux Sound Architecture Driver Initialized.
[    0.050648] clocksource: Switched to clocksource arch_sys_counter
[    0.058826] thermal_sys: Registered thermal governor 'step_wise'
[    0.059312] NET: Registered protocol family 2
[    0.059908] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.059942] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.060032] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.060169] TCP: Hash tables configured (established 8192 bind 8192)
[    0.060303] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.060372] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.060607] NET: Registered protocol family 1
[    0.061418] RPC: Registered named UNIX socket transport module.
[    0.061435] RPC: Registered udp transport module.
[    0.061441] RPC: Registered tcp transport module.
[    0.061446] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.062128] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    0.062408] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.064025] workingset: timestamp_bits=30 max_order=18 bucket_order=0
[    0.071939] NFS: Registering the id_resolver key type
[    0.071986] Key type id_resolver registered
[    0.071995] Key type id_legacy registered
[    0.072099] bounce: pool size: 64 pages
[    0.072149] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.072160] io scheduler mq-deadline registered
[    0.072167] io scheduler kyber registered
[    0.073565] sun4i-usb-phy 1c13400.phy: Couldn't get regulator usb1_vbus... Deferring probe
[    0.077276] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.138105] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.140133] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[    0.141251] printk: console [ttyS0] disabled
[    0.161464] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 48, base_baud = 1500000) is a U6_16550A
[    0.783496] printk: console [ttyS0] enabled
[    0.788165] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
[    0.818781] 1c29000.serial: ttyS1 at MMIO 0x1c29000 (irq = 49, base_baud = 1500000) is a U6_16550A
[    0.828217] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator
[    0.858783] 1c29c00.serial: ttyS2 at MMIO 0x1c29c00 (irq = 50, base_baud = 1500000) is a U6_16550A
[    0.980695] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
[    0.988185] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[    0.994099] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    1.003073] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc 
[    1.012132] scsi host0: ahci-sunxi
[    1.015997] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 36
[    1.025865] libphy: Fixed MDIO Bus: probed
[    1.029970] CAN device driver interface
[    1.034442] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pa not found, using dummy regulator
[    1.044269] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
[    1.050673] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
[    1.056696] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[    1.062469] sun7i-dwmac 1c50000.ethernet: no reset control found
[    1.069289] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.075873] ehci-platform: EHCI generic platform driver
[    1.081552] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.087753] ohci-platform: OHCI generic platform driver
[    1.095225] sunxi-rtc 1c20d00.rtc: registered as rtc0
[    1.100417] i2c /dev entries driver
[    1.104979] axp20x-i2c 0-0034: AXP20x variant AXP209 found
[    1.125388] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-0034/axp20x-pek/input/input0
[    1.135329] axp20x-regulator axp20x-regulator: regulators node not found
[    1.142092] ldo1: supplied by regulator-dummy
[    1.146707] ldo2: supplied by regulator-dummy
[    1.151781] ldo3: supplied by regulator-dummy
[    1.156774] ldo4: supplied by regulator-dummy
[    1.161351] ldo5: supplied by regulator-dummy
[    1.166359] dcdc2: supplied by regulator-dummy
[    1.171460] dcdc3: supplied by regulator-dummy
[    1.177057] axp20x-i2c 0-0034: AXP20X driver loaded
[    1.183490] Registered IR keymap rc-empty
[    1.187609] rc rc0: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0
[    1.194455] input: sunxi-ir as /devices/platform/soc/1c21800.ir/rc/rc0/input1
[    1.202092] sunxi-ir 1c21800.ir: initialized sunXi IR driver
[    1.209020] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    1.219831] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pf not found, using dummy regulator
[    1.230380] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[    1.260486] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB
[    1.268627] sunxi-mmc 1c12000.mmc: allocated mmc-pwrseq
[    1.299266] sunxi-mmc 1c12000.mmc: initialized, max. request size: 16384 KB
[    1.302384] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.306875] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pg not found, using dummy regulator
[    1.317295] mmc0: new high speed SDHC card at address 5048
[    1.324536] sun4i-ss 1c15000.crypto-engine: Die ID 0
[    1.330189] mmcblk0: mmc0:5048 SD32G 29.0 GiB 
[    1.338024] usbcore: registered new interface driver usbhid
[    1.344457] usbhid: USB HID core driver
[    1.346982]  mmcblk0: p1
[    1.351023] ata1: SATA link down (SStatus 0 SControl 300)
[    1.356923] random: fast init done
[    1.363557] debugfs: Directory '1c22c00.codec' with parent 'sun4i-codec' already present!
[    1.373414] sun4i-codec 1c22c00.codec: Codec <-> 1c22c00.codec mapping ok
[    1.381689] NET: Registered protocol family 17
[    1.386164] can: controller area network core (rev 20170425 abi 9)
[    1.392487] NET: Registered protocol family 29
[    1.396933] can: raw protocol (rev 20170425)
[    1.401216] can: broadcast manager protocol (rev 20170425 t)
[    1.406876] can: netlink gateway (rev 20190810) max_hops=1
[    1.412641] Key type dns_resolver registered
[    1.417082] Registering SWP/SWPB emulation handler
[    1.437244] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pa not found, using dummy regulator
[    1.447099] sun7i-dwmac 1c50000.ethernet: IRQ eth_wake_irq not found
[    1.453482] sun7i-dwmac 1c50000.ethernet: IRQ eth_lpi not found
[    1.459514] sun7i-dwmac 1c50000.ethernet: PTP uses main clock
[    1.465289] sun7i-dwmac 1c50000.ethernet: no reset control found
[    1.477162] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[    1.484190] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.491166] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[    1.499341] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[    1.520262] mmc1: new high speed SDIO card at address 0001
[    1.590914] sun7i-dwmac 1c50000.ethernet: Version ID not available
[    1.597106] sun7i-dwmac 1c50000.ethernet:    DWMAC1000
[    1.602110] sun7i-dwmac 1c50000.ethernet: DMA HW capability register supported
[    1.609325] sun7i-dwmac 1c50000.ethernet: Normal descriptors
[    1.614996] sun7i-dwmac 1c50000.ethernet: Ring mode enabled
[    1.620811] libphy: stmmac: probed
[    1.626170] ehci-platform 1c14000.usb: EHCI Host Controller
[    1.631828] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
[    1.639891] ehci-platform 1c14000.usb: irq 33, io mem 0x01c14000
[    1.680648] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
[    1.687680] hub 1-0:1.0: USB hub found
[    1.691508] hub 1-0:1.0: 1 port detected
[    1.696375] ehci-platform 1c1c000.usb: EHCI Host Controller
[    1.702022] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
[    1.710086] ehci-platform 1c1c000.usb: irq 37, io mem 0x01c1c000
[    1.740663] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[    1.747614] hub 2-0:1.0: USB hub found
[    1.751447] hub 2-0:1.0: 1 port detected
[    1.756318] ohci-platform 1c14400.usb: Generic Platform OHCI controller
[    1.762994] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
[    1.771038] ohci-platform 1c14400.usb: irq 34, io mem 0x01c14400
[    1.845520] hub 3-0:1.0: USB hub found
[    1.849319] hub 3-0:1.0: 1 port detected
[    1.854228] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[    1.860920] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
[    1.869354] ohci-platform 1c1c400.usb: irq 38, io mem 0x01c1c400
[    1.945524] hub 4-0:1.0: USB hub found
[    1.949320] hub 4-0:1.0: 1 port detected
[    1.953791] sunxi-rtc 1c20d00.rtc: setting system clock to 1970-01-01T00:00:25 UTC (25)
[    1.962210] ALSA device list:
[    1.965184]   #0: sun4i-codec
[    1.981438] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[    1.989608] VFS: Mounted root (ext4 filesystem) readonly on device 179:1.
[    1.998536] devtmpfs: mounted
[    2.002716] Freeing unused kernel memory: 1024K
[    2.010811] Run /sbin/init as init process
[    2.496357] systemd[1]: System time before build time, advancing clock.
[    2.533898] systemd[1]: Failed to lookup module alias 'autofs4': Function not implemented
[    2.580292] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN -PCRE2 default-hierarchy=)
[    2.602558] systemd[1]: Detected architecture arm.
 
Welcome to Mageia 7!
 
[    2.646977] systemd[1]: Set hostname to <pi.raspberry>.
[    2.972819] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    2.990295] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    3.445516] random: systemd: uninitialized urandom read (16 bytes read)
[    3.454870] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[  OK  ] Listening on Device-mapper event daemon FIFOs.
[    3.490947] random: systemd: uninitialized urandom read (16 bytes read)
[    3.497678] systemd[1]: Reached target RPC Port Mapper.
[  OK  ] Reached target RPC Port Mapper.
[    3.554664] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[    3.562884] random: systemd: uninitialized urandom read (16 bytes read)
[    3.569596] systemd[1]: Reached target Swap.
[  OK  ] Reached target Swap.
[    3.602380] systemd[1]: Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-serial\x2dgetty.slice.
[  OK  ] Created slice system-getty.slice.
[  OK  ] Created slice User and Session Slice.
[  OK  ] Listening on Journal Socket (/dev/log).
[  OK  ] Listening on initctl Compatibility Named Pipe.
[  OK  ] Listening on udev Control Socket.
[  OK  ] Listening on udev Kernel Socket.
[  OK  ] Reached target Slices.
[  OK  ] Listening on Process Core Dump Socket.
[  OK  ] Started Forward Password R��…uests to Wall Directory Watch.
[  OK  ] Listening on Journal Socket.
         Mounting Kernel Debug File System...
         Starting udev Coldplug all Devices...
         Starting Load legacy module configuration...
         Starting Load Kernel Modules...
         Starting Journal Service...
         Starting Remount Root and Kernel File Systems...
         Mounting Temporary Directory (/tmp)...
         Starting Setup Virtual Console...
[  OK  ] Reached target Remote File Systems.
[  OK  ] Mounted Kernel Debug File System.
[    4.350876] EXT4-fs (mmcblk0p1): re-mounted. Opts: (null)
[  OK  ] Started Load legacy module configuration.
[  OK  ] Started Journal Service.
[  OK  ] Started Load Kernel Modules.
[  OK  ] Started Remount Root and Kernel File Systems.
[  OK  ] Mounted Temporary Directory (/tmp).
[  OK  ] Started Setup Virtual Console.
         Starting Rebuild Hardware Database...
         Starting Configure read-only root support...
         Starting Create System Users...
         Starting Apply Kernel Variables...
         Starting Flush Journal to Persistent Storage...
[  OK  ] Started Create System Users.
         Starting Create Static Device Nodes in /dev...
[  OK  ] Started Apply Kernel Variables.
[  OK  ] Started Configure read-only root support.
         Starting Load/Save Random Seed...
[    4.954111] systemd-journald[98]: Received request to flush runtime journal from PID 1
[  OK  ] Started Create Static Device Nodes in /dev.
[  OK  ] Started Load/Save Random Seed.
[  OK  ] Started Flush Journal to Persistent Storage.
[  OK  ] Started udev Coldplug all Devices.
         Starting udev Wait for Complete Device Initialization...
[  OK  ] Started Rebuild Hardware Database.
         Starting udev Kernel Device Manager...
[  OK  ] Started udev Kernel Device Manager.
         Starting Show Plymouth Boot Screen...
[  OK  ] Started Show Plymouth Boot Screen.
[  OK  ] Started Forward Password R��…s to Plymouth Directory Watch.
[  OK  ] Reached target Paths.
[  OK  ] Found device /dev/ttyS0.
[  OK  ] Reached target Sound Card.
[  OK  ] Started udev Wait for Complete Device Initialization.
         Starting Activation of LVM2 logical volumes...
[  OK  ] Started Activation of LVM2 logical volumes.
[  OK  ] Reached target Local Encrypted Volumes.
         Starting Activation of LVM2 logical volumes...
[  OK  ] Started Activation of LVM2 logical volumes.
         Starting Monitoring of LVM�…meventd or progress polling...
[  OK  ] Started Monitoring of LVM2�… dmeventd or progress polling.
[  OK  ] Reached target Local File Systems (Pre).
[  OK  ] Reached target Local File Systems.
         Starting Tell Plymouth To Write Out Runtime Data...
         Starting Restore /run/initramfs on shutdown...
         Starting Create Volatile Files and Directories...
         Starting Rebuild Dynamic Linker Cache...
         Starting Reconfigure the s��…em on administrator request...
[  OK  ] Started Tell Plymouth To Write Out Runtime Data.
[  OK  ] Started Restore /run/initramfs on shutdown.
[  OK  ] Started Create Volatile Files and Directories.
         Starting Rebuild Journal Catalog...
         Starting Update UTMP about System Boot/Shutdown...
[  OK  ] Started Update UTMP about System Boot/Shutdown.
[  OK  ] Started Rebuild Journal Catalog.
[  OK  ] Started Reconfigure the system on administrator request.
[  OK  ] Started Rebuild Dynamic Linker Cache.
         Starting Update is Completed...
[  OK  ] Started Update is Completed.
[  OK  ] Reached target System Initialization.
[  OK  ] Listening on D-Bus System Message Bus Socket.
[  OK  ] Reached target Sockets.
[  OK  ] Reached target Basic System.
[  OK  ] Started Hardware RNG Entropy Gatherer Daemon.
         Starting OpenSSH Server Key Generation...
         Starting NTP client/server...
         Starting LSB: Nameserver information manager...
         Starting LSB: Checks if a ��…rtition is close to full up...
         Starting D-Bus System Message Bus...
         Starting Login Service...
         Starting LSB: Wait for the hotplugged network to be up...
[  OK  ] Started Daily Cleanup of Temporary Directories.
[  OK  ] Reached target Timers.
[  OK  ] Started D-Bus System Message Bus.
[  OK  ] Started Login Service.
[  OK  ] Started NTP client/server.
[   16.896405] sun7i-dwmac 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [Generic PHY]
[   16.921041] sun7i-dwmac 1c50000.ethernet eth0: No Safety Features support found
[   16.928393] sun7i-dwmac 1c50000.ethernet eth0: RX IPC Checksum Offload disabled
[   16.935797] sun7i-dwmac 1c50000.ethernet eth0: No MAC Management Counters available
[   16.943516] sun7i-dwmac 1c50000.ethernet eth0: PTP not supported by HW
[   16.950059] sun7i-dwmac 1c50000.ethernet eth0: configuring for phy/rgmii link mode
[  OK  ] Started LSB: Nameserver information manager.
         Starting LSB: Bring up/down networking...
[  OK  ] Started LSB: Checks if a partition is close to full up.
[  OK  ] Started LSB: Bring up/down networking.
[  OK  ] Started OpenSSH Server Key Generation.
[  OK  ] Started LSB: Wait for the hotplugged network to be up.
[  OK  ] Reached target Network.
         Starting OpenSSH server daemon...
         Starting Permit User Sessions...
[  OK  ] Reached target Host and Network Name Lookups.
[  OK  ] Reached target Network is Online.
[  OK  ] Started Permit User Sessions.
         Starting Hold until boot process finishes up...
[  OK  ] Started Command Scheduler.
         Starting Terminate Plymouth Boot Screen...
 
Mageia release 7 (Official) for armv7hl
Kernel 5.4.0-rc3 on a Dual-processor armv7l / ttyS0
pi login: bananapro
Password: [   32.490684] vcc3v0: disabling
[   32.493673] vcc5v0: disabling
 
Login incorrect
 
pi login: banana
Password: 
Login incorrect
 
pi login: banana
Password: 
Login incorrect
 
pi login: [   69.864339] random: crng init done
[   69.867760] random: 7 urandom warning(s) missed due to ratelimiting
banana
Password: 
Login incorrect
 
pi login: banana
Password: 
login: timed 
Mageia release 7 (Official) for armv7hl
Kernel 5.4.0-rc3 on a Dual-processor armv7l / ttyS0
pi login: banana
Password: 
Login incorrect
 
pi login: root
Password: 
Login incorrect
 
pi login: login: timed o
Mageia release 7 (Official) for armv7hl
Kernel 5.4.0-rc3 on a Dual-processor armv7l / ttyS0
pi login: 
 


Mais ne rigolez pas, les logins et mots de passes ne marchent pas...
   
Répondre
Vous n'êtes pas autorisé à écrire dans cette catégorie